wulfden::theshoppe::freeduino::burner

about | k107 | datasheets | diskshoppe | PRC | Freeduino | PICAXE | MSP430 | SX48 | FT817 | LaserTag | BS2 | Clearance | feedback

FREEDUINO Compatible Products

about | ADABOOT | BootBurner | resources | tutorials

Totally Open Arduino-Compatible Hardware Development

[Pictures below may be clicked to enlarge]

Wulfden Freeduino BB BootBurner

Burner with ZIF deck removed

Closeup of Burner board, Green LED is Power, Red LED is
Digital 13 progress indicator, 5 pin socket header in front is for
the P4, 2x3 header rear right is ISP, 1x6 header rear left is for
the FTDI cable, black wire has inline 2.1x5.5mm coaxial power socket

Burner set up to take power from and be programmed
by the FTDI TTL232R cable

Burner set up to take power from external supply and programmed
with the Wulfden P4 adapter, via a Keyspan USB to Serial adapter

This web page was last updated on Mon, 07 Jan 08 at 1237 hours

The name "Arduino" is a trademark of the Arduino team. The Arduino team has expressed the desire that the name "Arduino" should be used to refer only to products created and supported by the Arduino team; see the Arduino website for more information.
Many alternatively produced Arduino items are being created under the name Freeduino. The Wulfden and Modern Device products listed below are offered as Arduino compatible items. They are not specifically authorised Arduino products and are not supported or endorsed by the Arduino team.
For more information on the Arduino project, the Freeduino movement within the Arduino world, go to the Freeduino Universe web page.

Wulfden Freeduino BB Bootloader Burner

An Arduino(R) compatible processor board with ISP connector and ZIF socket to facilitate easy burning of Bootloaders and Sketchs to Arduino compatible AVR chips

Fully assembled and tested
accepts an Atmel ISP device with a 6 [pin ISP connctor. (6 to 10 pin optional adapter available)
Can be powered and sketches downloaded via FTDI TTL-232R cable
Also accepts Wulfden P4 programming adapter (RS232)
the 1.3 mmm connector nomral to the BBB has been replaced with a short pigtail and an inline 2.1mm connector
the Red LED on Digital 13 acts as a progress indicator for nurning and sketch downloading
You may request the 1.3mm power connector be left in place
You may request the LEds and P4 connector be left off so the entire Analog and Digital pins are accessible.
The ZIF socket assembly is removeable. It could be used on another board or assembly.

ORDER CONFIRMATION - Your PayPal receipt is your order receipt confirmation. Please consult the Shipping Status List (last updated on Thu, 04 Oct 07 at 1625 hours) your order status as pending, packed and/or has been shipped. All shipping is by US Postal Service (First Class Mail - domestic, Air Mail - foreign)
If you are located outside of North America, also please click here for the five dollars USD ($5.00) surcharge for shipping. This is a one time fee per order.
PayPal orders are generally sent within a day. You may order by mail with a Postal Money Order or a personal check; they must be made out in "US Funds." Orders paid by check will be held five days after receipt. Make checks or money orders out and send to:

Brian Riley
PO Box 188
Underhill Center, VT 05490

Wulfden Freeduino BB Bootloader Burner	This is a completely assembled and tested unit, based on the Rev D BBB. It comes with either a TexTool or Aries 28 pin ZIF socket, power and progress LEDs, 5 pin socket to accept P4 programming adapter, and a 2.1mm coaxial power connector. The price includes Priority Mail (US only) postage		Burner $38 pp*
If you want any of the variations in the build please include a note in the appropriate spot on Paypal form
The following items are priced based as add-ons to the BBBurner set. Orders for just the add-ons without an BBBurner will be returned!
ISP Adapter	small board with 2x3 socket header and 2x5 male pin headers to use a 10 pin ISP unit with this Burner. If this is ordered with Burner unit, the 2x3 ISP connector will be mounted upright.		$3
FTDI USB Programming Cable		This is the FTDI TTL-232R(5) cable with the USB-serial circuitry in the USB "A" end and a 6 pin .100" socket header at the other end. It implements TxD, RxD, RTS, CTS and supplies up to about 500 ma of 5 volt current. The FTDI Driver correctly responds to the AutoReset signal in Arduino-0009 by flagging RTS instead of DTR (in Mac/Linux its enabled, in Windows you need to enable).	FTDI Cable $20
P4 Programming Adapter		Wulfden P4 Serial Programming Adapter	$3