about | k107 | downloads | diskshoppe | PRC | Freeduino | PICAXE | MSP430 | SX48 | FT817 | LaserTag | BS2 | Clearance | feedback

K107 Serial LCD Controller Board - Order Page

about | K107 Orders | PIC-EL Upgrade

[Click on any picture below to enlarge]





















PayPal Seal

CUSTOMER EMAIL ADDRESSES - when you place an order with us here at Wulfden you need to supply us with a real email address for an account that is checked daily. Increasingly we get orders from dummy email addresses that are used just for PayPal and rarely/never checked. Thus, when something is not clear in an order and I attempt to remedy the situation I get no answers. I take no responsbility for your order beyond the face value of the PayPal order under these circumstances. A number of you have cute little traps set requiring secondary response to get mail through to your address. I do not play that game! Make <brianbr@wulfden.org> able to pass your trap.

Board -- Board and Parts -- Board and Chip
K107 (Rev4)
pcb only

Qty=1

$5 + $2

Qty=3

$15 + $2

Qty=5

$20 + $3

Qty=10

$40 pp
K107 (Rev4)
pcb & parts only
(no chip)

Qty=1

$9 + $2

Qty=3

$27 + $3

Qty=5

$40 + $4

Qty=10

$80 pp
Board & Chip (9600 baud) K107 (Rev4) pcb & LCD117 chip (9600 baud)

-recommended for general use-

Qty=1

$9 + $2

Qty=3

$27 + $3

Qty=5

$40 + $4

Qty=10

$80 pp
Board & Chip (19200 baud) K107 (Rev4) pcb & LCD117 chip (19200 baud)

-recommended for use with Arduino-

Qty=1

$9 + $2

Qty=3

$27 + $3

Qty=5

$40 + $4

Qty=10

$80 pp
Board & Chip (2400 baud) K107 (Rev4) pcb & LCD118 chip (2400 baud), and 4 MHz resonator

-recommended for use with PICAXE-

Qty=1

$9 + $2

Qty=3

$27 + $3

Qty=5

$40 + $4

Qty=10

$80 pp

All done ordering? Be sure to check out shipping surcharges

Full Kits ( board, parts, serial cable and chip)
Full KIt (9600 baud) K107 (Rev4) pcb, parts, serial cable & LCD117 chip (9600 baud)

-recommended for general use-

Qty=1

$15 + $2

Qty=3

$43 + $3

Qty=5

$70 + $5

Qty=10

$140 pp
Full KIt (19200 baud) K107 (Rev4) pcb, parts, serial cable & LCD117 chip (19200 baud)

-recommended for use with Arduino-

Qty=1

$15 + $2

Qty=3

$43 + $3

Qty=5

$70 + $5

Qty=10

$140 pp
Full KIt (2400 baud) K107 (Rev4) pcb, parts, serial cable & LCD118 chip (2400 baud), and 4 MHz resonator

-recommended for use with PICAXE-

Qty=1

$15 + $2

Qty=3

$43 + $3

Qty=5

$70 + $5

Qty=10

$140 pp

All done ordering? Be sure to check out shipping surcharges

Full Kit/Serial Cable/Display Bundles
2x16 Miniature Display Bundle

Full K107 Kit, new Hantronix backlit miniature high contrast 2x16 display, adapter board for the FFC ribbon connector and mounting hardware.

LCD117/9600

$23 + $4

LCD117/19200

$23 + $4

LCD118/2400

$23 + $4
2x16 Blue/White Display Bundle

Full K107 Kit, new full size backlit very high contrast 2x16 display, .

LCD117/9600

$25 + $3

LCD117/19200

$25 + $3

LCD118/2400

$25 + $3
2x24 Display Bundle

Full K107 Kit (board, chip, parts, and cable) bundled with a used, like-new non-backlit 2x24 display

LCD117/9600

$22 + $4

LCD117/19200

$22 + $4

LCD118/2400

$22 + $4
2x40 Display Bundle

Full K107 Kit (board, chip, parts, and cable) bundled with a new non-backlit 2x40 display

LCD117/9600

$23 + $4

LCD117/19200

$23 + $4

LCD118/2400

$23 + $4
4x20 Backlit Display Bundle

Full K107 Kit (board, chip, parts, and cable) bundled with a new, high contrast, Dark Gray letters on yellow green back ground 4x20 LED Backlit display. It will mount using a 1x16 straight pin header (supplied with kit) .

LCD117/9600

$28 + $4

LCD117/19200

$28 + $4

LCD118/2400

$28 + $4
4x20 Backlit Display Bundle

This offering is a complete K107 Kit (board, chip, parts, and cable) bundled with a new, very high contrast, White letters on Blue back ground 4x20 LED Backlit display. It will mount using a 1x16 straight pin header (supplied with kit) .

LCD117/9600

$32 + $4

LCD117/19200

$32 + $4

LCD118/2400

$32 + $4

All done ordering? Be sure to check out shipping surcharges

Assembled and Tested Units with serial cable
Item  

LCD117/9600

LCD117/19200

LCD118/2400
K107 Board A&T (partial)

Completely Assembled and Tested with serial cable, including an assortment of display connectors. No display connector is soldered in place, user must detrermine his need, select the appropriate connector and solder in place.
$20 + $4
$20 + $4
$20 + $4
K107 Board A&T (complete)

Assembled and Tested with serial cable - user must specify which connector is needed for his display - 1x10, 1x14,1x16, and/or 2x7, male (pins) or female (sockets), component side or solder side mounting (most 1x's will require sockets mounted on solder side of the k107).
$21 + $4
$21 + $4
$21 + $4
K107 Board A&T bundled with 2x40 LCD

K107 serial LCD controller with serial cable and new 2x40 display. Assembled, tested and setup for the display. K107 will mount to the back of the display by a standard 2x7 .100 spaced pin header and socket
$27 + $4
$27 + $4
$27 + $4
K107 Board A&T bundled with 2x24 LCD

K107 serial LCD controller with serial cable and used like-new condition 2x24 display. Assembled, tested and setup for the display.

$27 + $4
$27 + $4
$27 + $4
K107 Board A&T bundled with Miniature 2x16 LCD

K107 serial LCD controller with serial cable and used like-new condition Hantronix miniature (2.1" by 0.8") 2x16 backlit display. This unit uses a 16 conductor Flat Flex cable and comes with the K107RA adapter. Assembled, tested and setup for the display. Comes with mounting screws and nuts
$29 + $4
$29 + $4
$29 + $4
K107 Board A&T bundled with 4x20 Backlit Yellow/Gray LCD

K107 serial LCD controller with serial cable and brand new 4x20 Backlit Yellow/Gray LCD.
$34 + $4
$34 + $4
$34 + $4
K107 Board A&T bundled with Blue/White 2x16 LCD

K107 serial LCD controller with serial cable and new backlit blue/white 2x16 display. Assembled and tested
$30 + $4
$30 + $4
$30 + $4
K107 Board A&T bundled with 4x20 Backlit Blue/White LCD

K107 serial LCD controller with serial cable and brand new 4x20 Backlit Blue/White LCD.
$38 + $4
$38 + $4
$38 + $4

All done ordering? Be sure to check out shipping surcharges

Miscellaneous
Servo/LCD/Sensor Cable

Black/Red/White 14" (35 cm) cable, with .100 spaced female sockets (Molex KK) both ends plus 3 pin double male header/adapter to act as a gender bender. This cable is perfect for connecting a DS18B20 sensor in TO-92 case to a processor board or breadboard to make off-board measurements.

One of these cables is part of each full K107 kit so there is no need to order it for that purpose.

I stock this cable as a conveniece. I will only sell small quantities with orders of K107's, FKits, DS18B20's etc at the time of purchase of these items. This cable is not for sale by itself. Any order for just the cable or cables will be returned and refunded.

Qty = 1

$2.25

Qty = 3

$6.00
K107RA - FFC/FPC Ribbon Adapter

This board will provide an adaptation of the K107 to displays making use of 16 conductor "Flat Flex" (FFC/FPC) cables. It maybe be plugged into the 1x16 socket header on the K107 or soldered directly to the row of 16 holes without the socket header.

Kit consists of the K107RA board, a 1x16 pin header and a 16 contact FFC/FPC through hole socket that has to be soldered surface style to the edges of both sides of the pcb. Assembly time less than 5 minutes.

Qty = 1

$3.00 + $2

Qty = 2

$5.00 + $2

Qty = 3

$7.00 + $2

All done ordering? Be sure to check out shipping surcharges